Free Tutorial: Stardrop Table Topper

This fun Octagon shaped Stardrop Table Topper was designed with EQ8 Quilt Design Software by The Electric Quilt Company .  This tutorial takes that design and gives you the information to make it yourself.  This is a very easy beginner foundation pieced mini quilt but it is helpful to have some basic knowledge of paper piecing.  you will assemble eight units to combine to create the top of this little quilt.  I made this with gradations of aqua and teal solid cotton fabrics and the background is a lovely linen.  This is the perfect base for your table centerpiece.

Stardrop Table Topper

Finished size is approximately 24″ x 24″

Materials

  • 1/8 yd of light aqua cotton
  • 1/8 yd of medium aqua cotton
  • 1/8 yd of teal cotton
  • 1 yd for background, backing and binding
  • 28″ square piece of batting
  • Stardrop Template 1
  • Stardrop Template 2
  • 16 sheets of EQ printable Foundation Sheets or other foundation paper

HINT:  Have you tried printing on EQ Printables Foundation Sheets?  EQ has 25 sheet packages of special nonwoven material that you can run through your printer just like paper.  It tears away easily, is translucent and won’t dull machine needles. If you don’t want to print, you can also use a pen, pencil or marker to draw your template onto the paper.  Electric Quilt generously provided the foundation sheets for this project.

Directions

Cut Fabric:

From light aqua, cut:

  • 8 — 4 1/2 ” x 5″ rectangles

From medium aqua, cut:

  • 8 — 5″ x 7″ rectangles

From dark teal, cut:

  • 8 — 5″ x 10″ rectangles

From the dark linen, cut:

  • 1 – 28″ square for the backing
  • 16 — 2 1/2″ x 6″ rectangles for top template background
  • 16 — 3″ x 7″ rectangles for bottom template background
  • 8 — 2″ x 11″ strips for bottom template background
  • 95″ x 2 1/4″ strips for binding (can be pieced together)

 

Paperpiecing

 

  1. Use a pencil to trace the foundation pattern once onto EQ Printables Foundation sheets or other lightweight copy or foundation piecing paper of your choice. You can also print a copy of the foundation pattern onto lightweight copy or foundation piecing paper.  EQ generously provided the foundation sheets for this project.  The sheets feel like a soft stabilizer, they easily went through my inkjet printer.  I like that you can see through them so it is easy to match up fabrics from the backside.  It is super easy to sew through and it is not as stiff as paper.
  1. Use a very short machine stitch, I use 1.8 mm so the paper will tear off easily later.
  1. To foundation paper piece, stitch fabric pieces to a foundation paper with the marked side of the paper facing up and the fabric pieces layered underneath. The resulting pieced unit is a mirror image of the foundation paper.

  1. Using the larger template and starting in the number order, place the first two fabric pieces, RST, on the back side of the foundation paper with the edges of the fabrics extending ¼” beyond the first stitching line. The first stitching line is between section A1 and A2.
  1. Holding the pieces in place, stitch from the top side on the line between the two areas, starting and stopping just past the seam allowances.
  2. Above,  you see the back side of the pieces we just stitched.
  3. Flip the piece back over and fold the paper back on the line you just sewed.
  4. Using a ruler, trim the seam to 1/4″. Be careful not to cut through your paper template.
  5. Fold the paper back and flip it over again.
  6. Open out the piece and press the seam. The right sides of the fabrics will show on the back side of the paper template.
  7. Continue to add pieces in order step by step until you have finished the bottom template.
  8. Trim the bottom template around the outside seam allowance on the paper.
  9. Use the same method to sew the top template pieces.
  10. Carefully sew the top and bottom foundation templates together.  You should have a total of 8 triangle shapes.
  11. Sew together the paper pieced shapes, two at a time, aligning seams and points.
  12. Then stitch together the pieces to form two halves.  Now you can sew together the two halves, aligning the center points and seams.
  13. Carefully tear off the foundation pattern when you have finished the block

Assemble the Stardrop Table Topper

  1. Make a quilt sandwich with the quilt top, batting and backing.
  2. Baste the quilt layers together.
  3. Quilt as desired.  I used some free motion feathers and leafy motifs in the triangles.
  4. Sew the 2 1/4″ strips together for the binding and add to the quilt.  You are finished!

I would love to see your Stardrop Table Topper Quilt, tag me on instagram @lorimillerdesigns.

Looking for the EQ8 Design Instructions?  This quilt was designed in two parts, follow the links below:

EQ8 Stardropper Table Topper Design – Part 1

EQ8 Stardropper Table Topper Design – Part 2

For more projects and tips and techniques on using EQ8, visit my Electric Quilt blog series EQ8 Lessons with Lori.

For more information on EQ8, go to Electric Quilt 8 Software.